Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Westchester
When a driveway gate stops latching, drags on its track, or won’t open at all, we’re the team Westchester homeowners call to get it working again. We work on the gate you have, whether it’s an old wrought-iron swing gate bolted to a block-wall post on a small lot off Bird Road or a newer aluminum slider tucked behind a perimeter wall near Coral Way. Our technicians have up to 11 years of experience with residential and commercial gate systems, and we know how Westchester’s tight lots, block walls, and storm-season wind loads change what a repair actually looks like. Call (877) 802-1841. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Westchester Homeowners Call Gate Repair Davie for Gate Repair
We serve Westchester because it’s a pocket that punishes gate systems in a particular way: dense single-family lots, perimeter walls, and decades-old hardware that was never built for the operator bolted onto it years later. That’s not a guess. It’s the pattern our technicians see on residential swing and sliding gate calls here again and again, and it’s why we lead with repair instead of replacement.
Our gate repair team works across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so there’s no figuring out your equipment on your dime. We can work with your insurer when storm damage is involved, and we always quote and agree on the price before any work starts. If you’re calling about a gate that closes but won’t latch, mention that up front – it changes what we check first.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Wrought Iron Gate Repair in Westchester
Wrought Iron Gate Repair in Westchester usually comes down to old iron hanging on original hinge hardware that has been retrofitted with a newer operator over the years. On the 1950s – 1970s ranch lots that fill this area, the gate is often bolted directly to a concrete-block perimeter wall rather than a freestanding steel post. That means the fix is frequently at the hinge post and its footing, not the panel. Typical wrought iron gate repair in Westchester runs $180 – $480 depending on whether we’re resetting hardware, realigning the gate, or welding a rusted frame back to solid.
Corrosion and Hinge Wear on Old Iron
South Florida’s salt-laden humid air and heavy summer rain corrode hinges and rack and pinion components faster than they would in a drier climate. When a gate binds, twisted hinge plates or a worn pin are often the culprit. We replace corroded hardware with components rated for Miami-Dade wind loads so the gate swings true and holds.
Weld and Rust Repair
Rust at the bottom rail and weld failures at the hinge corners are common on decades-old iron. We clean back the corrosion, weld the frame where it has opened, and check the gate sits square in the opening before we adjust anything on the operator. If the frame is too far gone to repair safely, we’ll tell you plainly rather than patch it.
Metal Gate Repair in Westchester
Metal Gate Repair in Westchester covers the aluminum sliders and tubular steel swing gates on nearly every lot behind a block wall. The recurring issue here is a gate that still closes but no longer latches, or an operator straining against a gate that has dropped a half-inch. Typical metal gate repair in Westchester runs $150 – $420, with realignment and post work at the higher end. A qualified technician checks the post footing and wall first, corrects sag at the hinge post rather than the panel, and verifies the safety photocells still trip before calling the job done.
Post-Storm Misalignment
After a named storm, our technicians get a wave of calls for gates that close but won’t latch. Wind racks the block-wall post just enough that old swing hardware binds. The driveway gate is the visible symptom of a shifted post, so shimming the latch won’t hold – we reset the post and footing first.
Tracking and Slider Hardware
On sliding gates, worn rollers and a track that has filled with grit or rusted cause the gate to jump or drag. We clean or replace the track, swap the rollers, and check the gate stops where it should. If the operator is a Mighty Mule or Ghost Controls unit, we’re familiar with the DIY-entry systems and their common failure points.
Trusted Brands We Service in Westchester
We work on the system you have, not just the brands a company prefers to sell. That covers LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, spanning residential swing and slide operators through professional-grade commercial systems. We don’t claim to stock parts, so we’ll confirm what your gate needs and order it rather than promise a same-day fix we can’t deliver. From a broken arm or a bad control board to a full installation, it’s one point of contact for diagnosis, repair, and replacement when a gate is genuinely beyond saving.
Common Gate Repair Problems We See in Westchester Homes
- Gates that close but won’t latch after a storm. Wind racks the block-wall hinge post just enough that old swing hardware binds. The latch isn’t the problem – the post has shifted, so that’s what we reset.
- Corroded hinges and rack and pinion components. The humid, salt-laden air here eats through gate hardware faster than in drier climates. We replace corroded parts with wind-load-rated components that hold up.
- Operators bolted onto frames too old to carry them. A newer LiftMaster or Linear operator on an original 1950s – 1970s gate frame strains against a panel that has sagged or warped out of spec.
- Sagging gates on aging posts. Decades-old iron and aluminum gates drop at the hinge post as the footing and wall settle. Sag correction at the post usually beats replacing the whole gate.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Westchester, FL
Gate repair pricing here is set per job by the written estimate, but typical ranges give you a starting point. Wrought iron gate repair runs $180 – $480 in Westchester. Metal gate repair runs $150 – $420. Post and footing work after a storm sits toward the higher end because it’s more involved than swapping a hinge. Electric gate repair – motors, control boards, and safety sensors – runs $220 – $650 depending on the operator and parts needed. The price is always quoted and agreed before any work starts, so an invoice doesn’t come back bigger than the number you approved. Estimates are free.
We Also Serve Cities Near Westchester
We cover the neighborhoods and towns around Westchester, including Olympia Heights, Fountainebleau, Coral Terrace, and Tamiami. If your gate is in one of these nearby areas, the same local knowledge about block-wall posts, storm-season wind loads, and aging hardware applies. Call (877) 802-1841 for a free estimate and we’ll confirm coverage and timing for your address.
Serving Westchester, FL – Our Local Coverage Area
We serve Westchester and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Westchester
Because the wind has racked the concrete-block hinge post just enough that the swing hardware binds – the gate is usually fine, but the post has shifted. That block-wall post failure pattern is common on Westchester’s small-lot perimeter-wall gates and rare on properties with freestanding steel posts or commercial systems on wider setbacks. The fix is post and footing work, not panel work. Call (877) 802-1841 for a free estimate.
Yes, a solar opener can work on either a swing or slide gate here, provided the panel and battery are sized for the operator and the gate doesn’t bind. The gate has to move freely first – a sagging gate fights the operator and drains the battery. We check the hardware before recommending any power source. Call (877) 802-1841 to talk through your setup.
Not usually. Sag on a Westchester gate is most often at the hinge post or its footing, not the panel, so sag correction at the post resolves it without a new gate. We only recommend replacement when the frame itself is rusted through or too far out of square to repair safely. Call (877) 802-1841 for a free estimate.
Yes – an automatic gate should have working safety photo-eyes as a basic safety requirement. On the tight lots here, a child or pet can be under the gate line in seconds, and a failed photocell is a serious hazard. We test them as part of any operator or control board repair and replace them when they don’t trip. Call (877) 802-1841 to have yours checked.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, from residential swing operators to professional-grade commercial units. We work on the system you have rather than pushing a single brand. Call (877) 802-1841 and tell us the brand – we’ll confirm before we come out.
Get Your Westchester Gate Working Again
Whether it’s a gate that won’t latch after a storm, a corroded hinge, or an operator straining on an old frame, we can diagnose it and get it working. Call (877) 802-1841 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Davie.